laurence1
Básico
Marinero capaz · 29 pts
Virkie, Shetland Islands, United Kingdom
Miembro desde Dic 2015
Último en línea hace 11 años
Subidas recientes
Última actividad
Última publicación hace 11 años
Sea QueenHello again everyone, I've looked and found a 12v 2200mAh battery pack. in your opinion would this work well with a 900 motor? Also do you have any idea what sort of run time I would get?2,572 viewsSea QueenThanks Dave for your reply, I bought a Sea Queen model kit last year and built it but wasn't happy to be prepaired to put in the water. I had problems with the prop shaft and the keel of the boat. I'm not sure…2,572 viewsSea QueenHI Dave, I'd quite like to try fitting a brushless set up in it but I've never worked with brushless or lipos before. Any recommendations would be welcome.2,426 viewsSea QueenHello folks, that's my latest edition arrived today, and original Sea Queen in quite good condition, hopefully it won't take much to refurbish and get back into the water.
13 replies3,606 viewsSea CommanderThanks Alan, I did wonder wether or not to smack it out with a hammer. I've also got delamination of the ply on the port side of the main cabin above the window, going to try and glue it back together as would…1,581 viewsSea CommanderThanks Colin, I've never done this before so extracting it will be pretty much like brain surgery carried out by a numpty!! I'll wait until the new one arrives then give it a go! Until then I'll get the paint …1,581 viewsSea CommanderHello folks, I've decided to replace the prop shaft from my Sea Commander and replace it with a new stainless component. However the original shaft and tube is in place clatched in resin! How would going about…11 replies2,265 viewsAero kits sea commanderThanks very much Paul, I was planning to use the Johnson 600 in my Sea Commander. I've built a few boats but not really ever used them in the water so not up to speed with rc stuff. I was planning on using a b…1,319 viewsAero kits sea commanderThanks Dave, yes I've been building models for years. My grandfather was a real boat builder and he built a few models boats which I'm lucky to have kept after he died. There are a few issues with Sea Commande…1,319 viewsAero kits sea commanderAnother picture, not sure how to put a couple up at a time, sorry.
1,319 views
13 replies3,606 viewsSea CommanderThanks Alan, I did wonder wether or not to smack it out with a hammer. I've also got delamination of the ply on the port side of the main cabin above the window, going to try and glue it back together as would…1,581 viewsSea CommanderThanks Colin, I've never done this before so extracting it will be pretty much like brain surgery carried out by a numpty!! I'll wait until the new one arrives then give it a go! Until then I'll get the paint …1,581 viewsSea CommanderHello folks, I've decided to replace the prop shaft from my Sea Commander and replace it with a new stainless component. However the original shaft and tube is in place clatched in resin! How would going about…11 replies2,265 viewsAero kits sea commanderThanks very much Paul, I was planning to use the Johnson 600 in my Sea Commander. I've built a few boats but not really ever used them in the water so not up to speed with rc stuff. I was planning on using a b…1,319 viewsAero kits sea commanderThanks Dave, yes I've been building models for years. My grandfather was a real boat builder and he built a few models boats which I'm lucky to have kept after he died. There are a few issues with Sea Commande…1,319 viewsAero kits sea commanderAnother picture, not sure how to put a couple up at a time, sorry.1,319 views