Double Rum
Básico
Petty Officer 2ª clase · 320 pts
PLAINSVILLE, Canada
Miembro desde Mayo 2023
Último en línea hace 4 meses
Double Rum’s puerto
3 barcosHMCS ASSINBOINE (Ex:KEMPENFELT)
Hello everyone, today I acquired a model that I build 35 years ago. HMCS ASSINBOINE. At the time I built th…
Foundation Franklin
Hello All, Here is a model i built from scratch about 30 years ago. Im still adding things to her. She is 3…
HMCS SACKVILLE
Hello All, I built this model of HMCS Sackville to the scale of 1/4" to the foot about 20 years ago. I have…
Double Rum’s blogs de construcción
3 blogsHMCS GLENSIDE
Hello everyone, I’m currently building 1/32nd model of the Canadian WW2 tug Glenside. The tug was built for the Canadian navy in the fort…
13
10
9
Foundation Franklin Refit
Im beginning to do a long overdue refit on the Foundation Franklin. I built the ship over 30 years ago and is now time to clean her up an…
12
3
5
HMCS ASSINBOINE REFIT
Beginning the process of refitting. Will be mostly a cleaning/painting project but will make some additional parts add to the ship. Today…
6
2
4
Seguidores
3 seguidorsSubidas recientes
Última actividad
Última publicación hace 3 años
Re: Re: Drive assembly/ motor mountsYes, the oiler should function very well I believe.408 viewsDrive assembly updateI decided to change the drive arrangement. Instead of the wooden blocks for the motor bed i decided to use aluminum angle plate. I made the bearing plate adjustable to bring the thrust bearing end play to a mi…
+2♥ 13 likes662 viewsDrive assembly/ motor mountsToday I’m working on the motor mounts. I will drill holes in the mounts then epoxy studs in the holes. Then the motor will be secured with nuts. The motor is a 550 aristo craft Manuchi 550. It should be ok wit…
♥ 13 likes694 viewsNew bottom paintHello all, recently I repainted the bottom. Was long overdue as the coat of paint on her was the original paint.
♥ 12 likes660 viewsSpeed control/motorsThirty years ago this was the speed control that I purchased, from Dumas boats. It’s a resister type that uses a lot of power and needs a servo to operate. I will not be using it. She has two twelve volt Dumas…
♥ 6 likes635 viewsHMCS ASSINBOINE REFITBeginning the process of refitting. Will be mostly a cleaning/painting project but will make some additional parts add to the ship. Today I cleaned the tail shafts and propellers/ hubs. The props are 2 inch Du…
♥ 6 likes2 comments692 viewsTAIL SHAFT THRUST BEARINGHello, a little more progress. Today i made the shaft thrust bearing. Basically made from nylon and brass with two number 6-32 tpi set screws. The nylon was bored with a shoulder inside to be a press fit on th…
+1♥ 13 likes738 viewsRe: Fairey "Maybe" on the waterBeautiful design and model. She runs very nice!👍♥ 1 like2,365 viewsHMCS ASSINBOINE (Ex:KEMPENFELT)Hello everyone, today I acquired a model that I build 35 years ago. HMCS ASSINBOINE. At the time I built the model a friend on my wanted to get in to the hobby so I gave him this model. Well, it was in his bar…
+4415 viewsRe: Fairey "Maybe"Nice model and project. I really love the older models .♥ 3 likes654 views
+2♥ 13 likes662 viewsDrive assembly/ motor mountsToday I’m working on the motor mounts. I will drill holes in the mounts then epoxy studs in the holes. Then the motor will be secured with nuts. The motor is a 550 aristo craft Manuchi 550. It should be ok wit…♥ 13 likes694 viewsNew bottom paintHello all, recently I repainted the bottom. Was long overdue as the coat of paint on her was the original paint.♥ 12 likes660 viewsSpeed control/motorsThirty years ago this was the speed control that I purchased, from Dumas boats. It’s a resister type that uses a lot of power and needs a servo to operate. I will not be using it. She has two twelve volt Dumas…♥ 6 likes635 viewsHMCS ASSINBOINE REFITBeginning the process of refitting. Will be mostly a cleaning/painting project but will make some additional parts add to the ship. Today I cleaned the tail shafts and propellers/ hubs. The props are 2 inch Du…♥ 6 likes2 comments692 viewsTAIL SHAFT THRUST BEARINGHello, a little more progress. Today i made the shaft thrust bearing. Basically made from nylon and brass with two number 6-32 tpi set screws. The nylon was bored with a shoulder inside to be a press fit on th…+1♥ 13 likes738 viewsRe: Fairey "Maybe" on the waterBeautiful design and model. She runs very nice!👍♥ 1 like2,365 viewsHMCS ASSINBOINE (Ex:KEMPENFELT)Hello everyone, today I acquired a model that I build 35 years ago. HMCS ASSINBOINE. At the time I built the model a friend on my wanted to get in to the hobby so I gave him this model. Well, it was in his bar…+4415 viewsRe: Fairey "Maybe"Nice model and project. I really love the older models .♥ 3 likes654 views