Directorio del puerto
HMS Victorious
Fotos
Acerca de este barco
HMS Victorious....Circa 1941.
Based on a Fleetscale hull.Scale 1/128.
I started her some 5 years ago and it really has been a long job because of other projects which I prioritised.Thus it has been an on and off project.Still a lot to do in most area’s,so she is a long way off being finished with a lot of errors to rectify and modify.
Front lift goes up and down.
Rear turrets all turn.
Has a water steam smoke effect boiler.
Working bilge pump,plus more.
I also want to get the lifting crane to rotate, any ideas anyone, space is not at a premium?
Started on the Island only recently.
Had a trimming sail just prior to lockdown.She weighs a ton 🤔
This lockdown has boosted work much to the wife’s annoyance 😂😂
Will try to keep on top of this project now.
Regards Bill
Based on a Fleetscale hull.Scale 1/128.
I started her some 5 years ago and it really has been a long job because of other projects which I prioritised.Thus it has been an on and off project.Still a lot to do in most area’s,so she is a long way off being finished with a lot of errors to rectify and modify.
Front lift goes up and down.
Rear turrets all turn.
Has a water steam smoke effect boiler.
Working bilge pump,plus more.
I also want to get the lifting crane to rotate, any ideas anyone, space is not at a premium?
Started on the Island only recently.
Had a trimming sail just prior to lockdown.She weighs a ton 🤔
This lockdown has boosted work much to the wife’s annoyance 😂😂
Will try to keep on top of this project now.
Regards Bill
Le gusta a
Cargando…
Comentarios
Iniciar sesión para comentar.
GoBilda servos might serve you for your crane. fully proportional, they are capable of 300 degrees of rotation with a servo expander. Out of the box they give around 200 degrees or more, depending upon your radio.
ere I shuffle off this mortal coil😊
(Alas! Poor Yoric ... he's shuffled already!🤔)
😁😎
As always Doug you raise a smile 👍
Bill
PS.
Sorry Doug forgot to say great picture of your Graf spee 👍
That's an innovative and effective looking crash barrier you've given her Bill.
But shouldn't it be more up the sharp end? 😁😁
😎
Not the same as on the pond but better than nothing.
Take care and stay safe everyone.
Bill.
Thank you for the kind comments and thoughts on crane.
I will be investigating the ideas,which are sound.
Such a wealth of knowledge on this site 👍👍.
Sorry Ron I didn’t take any on the trim test as it was all a bit rushed,but I do have one somewhere I will dig out and post.
Roll on normality.
Bill
Cheers, Pete
1/128! 160cm. Same scale as my Graf Spee, 145cm.
Shame we don't live closer to sail them together.
I'd have to beef up my Flak battery first though😉
Ref rotating crane:
Can't you use the same mechanism as you used for the gun turrets?
For the guns on my destroyer I just used an old servo with a cog mounted on it.
Smaller cog on the turret shaft to extend the travel arc to +/- 120°.
Motion transfer from X to Y turret by 1to1 pulley.
Use a hollow tube for the pivot axis and you could also fit a small winch motor underneath, drum on a slow geared motor, and run a twirl cord through the tube to raise the jib😊
Operate via Left Stick or pot as Martin says.
Cheers, Doug 😎
On wonder she weighs a ton.
You have done a fantastic job so far.
I look forward to future updates.
As for the lifting crane how about a 360 servo with limit switches fitted and operated using a pot on your Transmitter.
Martin555.